Dv365etbgwr manual

These instructions should be kept for future reference. All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion.

Gas dryers are equipped with a burner vent for use with natural gas. An individual branch or separate circuit serving only your Dryer is recommended. Gas models — U. Page Installation - General Procedure Installation - General procedure For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side- by-side so you have easy access to both appliances. Page 18 installing your dryer 6. Three Wire system instructions: a. Loosen or remove the center terminal block screw.

Page Final Installation Checklist U. The dryer frame is grounded to the neutral conductor at the terminal block. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block.

Make sure your dryer is installed properly so it exhausts air easily. Tape all joints, including at the dryer. Unplug the power cord. Reinsert the black screw in the other hole.

Remove two door hinge screws. Lift the door and remove 4. Remove a screw on the 9. Reinsert the screw Step Frame Front. The indicator light by the cycle name will illuminate. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the load reaches the dryness level more dry to damp dry you selected.

Page 23 Wrinkle Prevent provides approximately minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling.

Press the Wrinkle Prevent Wrinkle Prevent button to activate this feature. Selection Button The indicator light above the pad will illuminate when you select Wrinkle Prevent. The load is dry and you can remove it at any time during the Wrinkle Prevent cycle. Once you turn Child Lock on, no button, except for the Power button, will respond until you release the Child Lock function. Open the Dryer door.

Position the drying rack in the tumbler, placing the front lip of the drying rack on top of the lint filter. Do not operate your dryer without the lint filter in place. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your Dryer and wipe up any spills or overspray immediately. If care label instructions are not available, use the following information as a guide.

Page Information Codes If the problem continues call for service. Invalid power source Frequency Try restarting the cycle. If the problem continues call for service. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items.

Follow care label directions to maximize garment life and reduce laundering problems. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance.

Page 41 Nous vous remercions d'avoir choisi ce produit Samsung. Remove the External ground connector screw.

Connect the ground wire green or unwrapped of the power cord to the external ground connector screw. If you want to connect B Green or bare copper wire of power cord to the Neutral Post without assembling with A cabinet ground , call the service technician.

Connect the neutral wire white or center wire of the power cord and the appliance ground wire green with yellow stripes under the central screw of the terminal block. Connect the other wires to the outer terminal block screws.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.

Please check your email for further instructions. Enter a new password. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need.

If the dryer is drawing amperages. Regulating thermostat trips easily or is open. When the dryer is operated on a heat setting, the igniter should be. If the igniter does not heat up, remove power and using an.

If the igniter heats up but the main burner flame is not ignited,. If a normal ignition takes place and after a short while the flame goes.