Cva 4062 manual

Remedy: 1. Check hose connections. Replace hoses, if necessary. Cause: Water container valve jammed or clogged. Check water container valve. Replace water container, if necessary. In service mode, without the brew unit, initialize the brew unit drive; see Table in Section If initialization is not possible, replace the brew unit drive. Remedy: Re-insert the guide correctly Figure , Item 1. Cause: Grind amount too high.

Remedy: Reduce the grind amount; Note: In order for the customer to be able to continue to prepare coffee and obtain hot water in the period before the service technician arrives, he or she can switch off the steam system. The top float in the water container has not switched within 5 minutes. Remedy: Confirm the fault message with OK. The values monitored for this depend on the set water hardness.

Cause: Defective triac on the power electronic. Remedy: Modified power electronic after machine no. Power electronic EPL , mat. To save and quit, press OK. Note: If the language is not set correctly, use the icon as a guide to get to the language setting. The machine can be safeguarded against Safety accidental switch-on.

System lock is switched off. Soft 1 0 - 4 grains per gallon Set the water hardness. The water Options: 1. Press OK to select the function. Accessing: 1. Press and hold Hot Water. Release Hot Water. Press Hot Water again 3 times; hold on the 3rd time until the service mode is displayed.

To prevent mechanical damage, always initialize as a last step. Home position The number of pulses from the flow meter will display. If this value is approximately 33, then the water flow is sufficient. Empty the water container or remove it from the appliance.

Compensation The grind amount compensation Microswitch switch is closed. Pull out the inlet filter behind the brass elbow using needlenose pliers.

Check and clean the inlet filter with hot water and a brush. The valve on the right is the primary valve; valve on the left, the secondary valve. Page Technical Service Bulletins Some machines will display no obvious symptoms.

Other functions of the coffee system are not affected. Page Cva Water Tank Cleaning days. There is no fault with the equipment and no reason to replace the tank.

The purpose of this conversion is to make the pipework more easily accessible to the customer for cleaning. Remove the milk container. Remove the 3 screws securing the right cover Figure 1, Item 1. Remove the cover.

Remove the 5 screws securing the central cover Figure 1, Item 2. Remove the front stainless-steel fascia piece from the central spout. Remove the central spout from the front. Slide the height adjustment mechanism upwards. Remove the 2 retaining spring clips Figure 3, Item 1. Remove the 4 screws securing the holder Figure 4, Item 1. Disconnect the connection to the left light Figure 4, Item 2. Figure 4 Remove the holder, as well as the complete height adjustment mechanism Figure Remove the 2 screws securing the central spout connection Figure 6, Item 1.

Remove the central spout connection. Figure 6 Install the new central spout connection Figure 7 in position and carefully tighten Our QRBP can be removed by hand.

Adjustable trigger with trigger guard actuated breech system. Synthetic stock with fiber-glass reinforcement in Veil Wideland. Whether you are looking for shirts, hats, or hoodies, we have them here for you. Stock Adjustable Cheek Rest. The HTR can produce muzzle velocities previously thought unattainable from a muzzleloader. Grayboe fiberglass stock. Stock Adjustable Cheek-piece. User profiles Revert The appliance can be set so that it Recommended frequency Every time mile is prepared, if there is more than one hour between uses Everyday at least at the end of the day, before you switch off the appliance Once a week Page Rinsing The System Allow the coffee system to cool before cleaning.

Danger of burns! Do not clean the unit with a steam cleaner. Never use cleaners containing chlorides, sand, soda or scouring agents. These will damage the surface. To avoid mold, growth and odors it is important to clean the machine regularly. Page Milk Pipework Cleaning and care Milk pipework Rinsing the milk pipework To prevent the milk residue from spoiling or drying in the machine and pipework, you should rinse these lines after use. In addition to rinsing after use, the lines need to be cleaned at the end of the day.

Page 43 Hang the cleaning container in the appliance where the milk container would normally sit. Use only Miele cleaning agent, which was developed especially for this coffee system.

You can obtain this cleaning agent from Miele. The cleaning process has now begun. Clean the whole part in the dishwasher without taking it apart. If there are milk residues in the milk pipework you can clean them with the cleaning brush provided.

To do this, take the cover and the milk pipework apart as follows: Do not pull the milk hoses off the Page Water Tank Water tank Empty the water tank daily and refill before preparing the first drink with fresh, cold tap water.

Check if the valve is clean. If the valve has residues on it, the water tank will not connect properly and might leak. Page Drip Tray Cleaning and care Drip tray The trip tray contains a sensor which causes the display to show when the tray is full and needs to be emptied. Clean the drip tray daily. Remove the drip tray after the final rinse when no more water runs from the lines.

Page Bean Container Bean container The bean container must be cleaned by hand with hot water and liquid dish soap. Do not use a dishwasher. The movable parts are lubricated and the cap will get damaged in the dishwasher. Do not use a dishwasher this will cause damage. Page 51 They are specially developed for the coffee maker to optimize the degreasing. The cleaning tablets can be purchased from Miele. As a reminder the display shows "Please run cleaning program" after cups and then until the machine is cleaned.

Page 52 Cleaning and care When the display prompts you to Please drop the cleaning tablet in the ground coffee funnel.

Page Descaling The Appliance They are specially developed for the coffee system to optimize the descaling. The descaling tablets can be purchased from Miele.

Other agents may damage the machine and affect the taste of coffee and hot water. The machine could also be damaged. Page Frequently Asked Questions If not, the lighting is defective. Solution — Turn the main switch to "I". Solution — The machine goes into standby mode when not used for a programmed time. Page 56 Frequently asked questions What if the machine does not switch on, even though the "Switch on at" timer setting is activated?

Possible fault The System Lock is activated. The display messages are difficult to read. Solution — Turn off the unit immediately. Service if the bean container is not empty. Otherwise fill the container with fresh beans. Solution Set the grind control slide to a finer grind. Possible fault — Were the supply lines and cup pre-heated?

No drink is prepared although the beans were grinded and enough water is in the container. Page 59 Instead of coffee only water is dispensed. Possible fault — The beans may have gotten stuck. The coffee system switches automatically back to bean use after preparation. Page 60 Frequently asked questions Water is in the waste unit. Possible fault This is not a fault. Possible fault — If the grind setting is too coarse, this can result in too much coffee water in the waste unit.

Page 61 The brew unit or waste unit could not be pulled from the machine.